Loading...

Crown Audio XTi 2002 475W Stero Power Amplifier With DSP

Special Price $789.00 Regular Price $1,398.00
SKU
CROWN-XTi2002
  • Manufacturer: Crown

•Peakx PlusTM Limiters provide the ultimate in system performance and protection by allowing full control over threshold, attack, and release •Enhanced Subharmonic Synth section provides user control over frequency, gain and filter type for system-specific tuning •3 User-defined fan mode controls – normal, early and full- speed – for matching fan performance to a specific application

More Information
MPN (manufacturer part number)XTi2002
UPC (Universal Product Code)00871015005317
ConditionNew
SpecsInput EQ 6 parametric filters per channel with adjustable Q, ±15 dB boost/cut. Also adjustable high and low shelving filters. This 8-filter EQ section can be bypassed.Crossover Filters Highpass and Lowpass per channel. Butterworth 6/12/18/24 dB per octave. Linkwitz-Riley 24/48 dB per Octave. Also includes ± 15 dB bandpass gain and polarity control.Output EQ 8 parametric filters per channel with adjustable Q, ±15 dB boost/cut. This 8-filter EQ section can be bypassed.Delay For signal alignment of driver; 50 mS of total delay.SubHarmonic Synth Takes the low-frequency content of the input signal and "synthesizes" a new signal that is the same as the input signal but one octave lower. The new synthesized signal is then mixed with the original signal to create the effect. New: Users now have control over frequency, gain, and filter type.Peakx™ Plus Limiter User defeatable limiter that allows users to control Threshold, Attack, and Release times.Presets 30 total presets, 29 of which are user-definable.Sensitivity (for full rated power at 4 ohms) 1.4 VrmsFrequency Response (at 1 watt, 20 Hz - 20 kHz) +0 dB, –1 dBSignal-to-Noise Ratio (below rated 1kHz power at 8 ohms) XTi2002: 100 dB (A weighted)Total Harmonic Distortion (THD) < 0.5%Damping Factor 20 Hz to 1 kHz > 500Crosstalk (below rated power) 20 kHz - 1 kHz: > 70 dbInput Impedance (nominal) 20k ohms balanced, 10k ohms unbalancedMaximum Input Signal +22 dBu typicalAC Line Voltage and Frequency Configurations 100 VAC, 120 VAC, 220-240 VAC 50/60 HzAC Line Current (120 VAC amplifier playing 1/8 power pink noise into 4 ohms per ch) XTi2002: 8.3A; no more than 38W at idleOperating Temperature 0°C to 40°C at 95% relative humidity (non-condensing)Level Two front-panel rotary level controls, one for each channelPower Switch On/Off switch applies AC power to the amplifierSel/Prev/Next Buttons Three buttons near the LCD screen that are used to access menu items and front panel lockoutLCD Screen Backlit liquid crystal display that shows preset and processing statusSignal Indicator Green LED, one per channel, illuminates when a very low-level signal is present at input (may be used for troubleshooting cable runs).–10 Indicator Green LED flashes when output signal exceeds -10 dB below clip.–20 Indicator Green LED flashes when output signal level exceeds -20 dB below clip.Ready Indicator Green LED, one per channel, illuminates when the amplifier is ready to produce audio.Clip Indicator Red LED, one per channel, turns on at the threshold of audible distortionTemp Indicator Red LED, one per channel, illuminates under excessive temperature conditionsPower Indicator Blue LED illuminates when the amplifier has been turned on and has powerInput Connectors XLR, one per channelLink/Out Connector Loop-thru signal from input connector for linking another amplifier, one per channel.Output Connectors Two Neutrik® Speakon® NL4MP output connectors. Channel-1 Speakon® is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs (in parallel with Speakon® connectors).HiQnet™ USB Connector Type B, connects to HiQnet™ network.Chassis SteelFront Panel Cast-aluminumCooling Proportional speed fan with front-to-rear airflow.Dimensions XTi 2002 19" (W) x 3.5" (H) x 12.25" (D)Net Weight XTi 2002 18.5 lbs (8.4kg)Shipping Weight XTi 2002 21.5 lbs (9.8kg)
Frequently Bought Together
  • Total price