QSC DSP-3 2 Channel Digital Signal Processor

$578.00

 
not_available
   

SKU
QSC-DSP-3

-Dual-Independent Channels of DSP -Features 48 kHz / 24-Bit Converters -Electronically Balanced Inputs -Contact Closure to Trigger Gain Changes
QSC DSP 3 2-Channel Digital Signal Processor DSP-3 (Digital Signal Processing) After three decades of developing pioneering audio products and systems, QSC raises the bar once again, setting a new standard in signal processing with the new DSP-3 Digital Signal Processing Module. The DSP-3's two channels of independent signal processing deliver more power, flexibility, and features-in short, more of everything you really need in a DSP-for less. Simple to install and compact, the DSP-3 is the advanced and affordable digital signal processing solution for your audio system. If you would like to purchase a DSP-3 module, please call our sales department at: 800-854-4079. Powerful The DSP-3’s powerful processor allows you to perform a wide range of signal processing functions. Whether you need speaker crossovers, EQ, time delay, or subsonic filters, the DSP-3 is as flexible as your systems's needs. Configurable The DSP-3’s processing horsepower is dynamically assignable so you’re not locked into a fixed configuration. Simply plug your laptop into its RS-232 serial interface and use QSC's powerful configuration software. You can easily configure multiple processing functions and signal flow with "click-and-drop" simplicity. The DSP-3 also allows real-time control or set-and-forget convenience. You can even save each configuration on disk for future recall. Versatile Getting attached to the DSP-3? Then you’ll be glad to know how easily it attaches to most two-channel DataPort-equipped QSC amplifiers, including the CX, DCA, and new PowerLight 2—without taking up extra rack space. Or use multiple DSP-3s with our rack-mount panel kit to create a stand-alone DSP solution that interfaces with any amplifier or system.
More Information
SKU QSC-DSP-3
Freeshipping Free Shipping
UPC (Universal Product Code) No
MPN (manufacturer part number) DSP-3
Discount No
Condition New
Features Hardware Two independent channels of DSP 48kHz, 24-bit converters No turn on pops or zipper noise If the memory or hardware fails, unit turns on muted Host interface via RS-232 or QSControl Audio Network System* via CM16a Amplifier Network Monitor Electronically balanced inputs Contact closure to trigger gain preset changes Post-DSP output signal for daisy-chaining Peak, RMS and Clip meter displays Selectable input sensitivity: 1.5, 4, 9, 13 Vrms; 6, 14.5, 21.5, 24.5 dBu; 3.5, 12, 19, 22.2 dBV DataPort "pass-through" compatible with QSControl Selectable output sensitivity: 4 Vrms or 6 Vrms Software "Drag-and-drop" configuration software DSP processing power and memory dynamically assignable to signal processing functions Graphical representation of DSP resources Firmware upgrades downloadable via RS-232 Hard copy printout of configuration layout or parameter settings
Specs Frequency Response Euro Input: 20Hz to 10kHz ±0.3dB Euro Input: 20Hz to 20kHz ±0.7dB DataPort: 20Hz to 20kHz ±0.2dB Distortion <0.01% THD+N @ +4dBu Dynamic Range Unweighted >93dB (20Hz to 20kHz for 1.5, 4 & 9V input sensitivities) >88dB (20Hz to 20kHz for 13V input sensitivities) Common-Mode Rejection Typical: >50dB (20Hz to 20kHz) Worst Case: >40dB @ 20 kHz Input Sensitivity (Selectable) 1.5, 4, 9 & 13Vrms 6, 14.5, 21.5 & 24.5dBu 3.5, 12, 19 & 22.2dBV Output Sensitivity 4Vrms / 6Vrms 14.5dBu / 18dBu 12dBV / 15.5dBV Inter-Channel Crosstalk DataPort: >75dB separation (20Hz to 20kHz) Input Connectors 3-pin Euros x 2 (one for each audio channel) Female HD-15 x 1 (DataPort) Female RS-232 x 1 (PC input) Power Jack x 1 (required only for PowerLight, QSC non-DataPort amplifiers, non-QSC amplifiers and using remote rack mounting bracket) Output Connectors 3-pin Euros x 2 (for daisy-chaining each audio channel out) HD-15 x 1 (male amplifier connection) LED Indicators Blue LED x 1: power (front) Green LED x 1: signal (front) External Power Requirements 15V DC / 0.4A (Required only for PowerLight, QSC non-DataPort amplifiers, non-QSC amplifiers and using remote rack mounting bracket) System Requirements Windows 98 / Windows NT4 (SP6) / Windows 2000 (SP1) SVGA monitor at 800 x 600 (minimum) SVGA monitor at 1024 x 768 (recommended) CD-ROM drive 32MB RAM (minimum) 10MB free hard disk space (minimum) Available RS-232 COM port Male to female 9-pin serial cable (for programming) (Windows Me not supported) Construction Steel chassis Steel back cover Dimensions (WxHxD) With Flanges: 4.8 x 3.5 x 1.2" (12.1 x 8.9 x 3.1 cm) Without Flanges: 3.3 x 3.5 x 1.2" (8.4 x 8.9 x 3.1 cm) Weight 9.6 oz (272.2 g)
Producut Video No

© 2008 - 2018 RK Audio • 188 Lauman Lane Hicksville NY 11801 • 516-597-5450 All Rights Reserved.